How to Ensure your Physical Data Sanitization Equipment meets the NIST 800-88 requirements
Short answer: For an R2v3 facility, destruction equipment meets the mark when each device type follows one of the three Appendix B routes (a Table 1 method, the NSA manual with EPL-listed equipment, or an independently verified method), the output matches the criteria, video is kept for at least 60 days, and operators are trained and evaluated.
Owning a shredder is not the same as being ready for an R2v3 audit. An auditor can pick a device type from your intake and ask you to show how that exact media is destroyed, what the output must look like, and where the records and video are. This article is for R2 facilities and ITAD operations that physically destroy data storage devices, and it shows how to line your equipment up with NIST SP 800-88 and R2v3 Appendix B before the auditor asks.
To check the source directly, read the full NIST SP 800-88 Rev. 2 (PDF) from NIST.
What R2v3 Appendix B requires for physical destruction
R2v3 treats physical destruction as one form of sanitization. Its Definitions section, in summary:
Under R2v3, sanitization means removing and destroying the data held on a data storage device so it cannot be recovered with commonly available software or techniques. It covers both logical and physical destruction of that data, and it also requires taking off every user label and marking and clearing activity logs. The right method depends on the device; the standard gives examples such as software overwriting, degaussing, shredding, incineration, disintegration, grinding and embossing.
Summary of SERI R2v3, Definitions (Sanitization), p. 9
For a wider view of the standard, see our R2v3 standard requirements summary.
When data storage devices are sanitized physically, Appendix B allows three ways to destroy them:
- A destruction method that Table 1 of Appendix B lists for that type of device.
- The NSA Storage Device Sanitization Manual, carried out with equipment that appears on NSA’s Evaluated Products List.
- Another physical destruction method, provided a competent expert has independently verified that it sanitizes effectively.
Summary of SERI R2v3, Appendix B – Data Sanitization, requirement (7), p. 27
Under the first route, Table 1 sets a method and a result for each device type. For hard drives and solid state storage, in summary:
| Device | Method | Expected result |
|---|---|---|
| Magnetic hard disk drives | Degauss and crush | Both are required: the drive is degaussed and crushed in a hard drive crusher |
| Shred or otherwise physically destroy | The platters end up in fragments | |
| Incinerate | The drive is melted down to metal | |
| Solid state storage (for example SIM cards, SDRAM, flash drives, boards with non-volatile flash memory, SSDs, phones and tablets) | Shred or disintegrate | The memory chips end up in fragments |
| Crush | Uses an SSD crusher built for crushing chip sets | |
| Incinerate | Burned to ash |
Any degausser used must carry the manufacturer’s rating for the type of media it is used on.
Summarized from SERI R2v3, Appendix B – Data Sanitization, Table 1, p. 28. The full table also covers magnetic tape, diskettes, optical disks, hard copy and other media.
Two further Appendix B requirements apply to every physical destruction run:
- If a customer, a legal requirement or the sensitivity of the information calls for a stricter destruction method, the facility has to apply whichever requirement is strictest.
- Video of all physical destruction of media has to be kept for a minimum of 60 days.
Summary of SERI R2v3, Appendix B – Data Sanitization, requirements (8) and (9), p. 28
The R2v3 passages above are Paradygm Consulting’s summaries of SERI’s R2 Standard Version 3.0 (R2v3), effective July 1, 2020, pp. 9 and 27–28, not the standard’s wording. Use the full standard and SERI’s current guidance, and confirm interpretations with your certification body.
Not every R2 facility is certified to Appendix B. SERI’s guidance describes facilities outside Appendix B that physically destroy data devices in accordance with NIST’s media sanitization guidelines (SERI: Data Destruction/Sanitization Methods and Processing).
Where NIST SP 800-88 Rev. 2 fits in an R2v3 program
NIST published SP 800-88 Revision 2 in September 2025, superseding Revision 1 from December 2014. Of its three methods (clear, purge and destroy), physical destruction equipment has to deliver destroy. NIST Revision 2, Sec. 3.1.3, says destroy techniques “render target data recovery infeasible using state-of-the-art laboratory techniques and results in the subsequent inability to use the ISM for the storage of data.” It names disintegrate, incinerate, melt, pulverize and shred as the techniques commonly associated with destroy, and cautions that bending, cutting or drilling may only partly damage a device.
Many R2 work instructions still send operators to Revision 1’s Appendix A tables. Revision 2 removed those media-specific appendices and now points to IEEE 2883 (see our IEEE 2883 data sanitization training), NSA specifications, or an organizationally approved standard. Our post on what changed in NIST SP 800-88 Rev. 2 covers the update.
R2v3 audit checklist for destruction equipment: 7 checks
1. Build a device-to-machine matrix by Appendix B route
For each device type on your intake list, write down the route you rely on (Table 1, the NSA manual with EPL-listed equipment, or an independently verified method), the machine, and the Table 1 criteria it must meet. Phones, tablets, SIM cards and boards with flash memory fall under solid state storage in Table 1, so a hard drive shredder alone may not cover them. Our Guide to Electronics Destruction Operations explains the terms.
2. Prove shredder and crusher output matches Table 1
Table 1 is written as outcomes: platters in fragments, memory chips in fragments, chip sets crushed in an SSD crusher. Inspect and record output samples against those outcomes. NIST adds that some destructive techniques lose effectiveness as data density and material hardness rise, and that pulverize and shred techniques for ISM should be avoided for anything but the lowest security categories of data. Where a customer contract or a law calls for stricter destruction, Appendix B (8) means the strictest requirement wins.
3. Keep NSA EPL evidence for your exact model
If you use the NSA route, keep a dated copy of the current NSA Evaluated Products List entry for your exact model. NSA keeps separate lists for hard disk drive destruction devices, magnetic degaussers, optical sanitization devices and solid state disintegrators, updates them as needed, and also publishes an expired products list.
4. Check degausser ratings: degauss and crush
Under Table 1, a degausser needs the manufacturer’s rating for the media in question, and hard drives on that route need crushing as well as degaussing. NIST Revision 2 goes further: degaussing “is not considered an approved destroy sanitization technique”, many existing degaussers lack the force for higher-coercivity media, and degaussing does not sanitize SSDs. Do not record a degauss-only step as destruction.
5. Show maintenance and calibration records
NIST lists equipment that is “not approved and/or improperly calibrated” as a reason to question whether sanitization was effective. Keep maintenance logs, cutter or screen inspections and output checks for each machine.
6. Link 60-day video, records and release
Keep the 60 days of destruction video Appendix B (9) requires, and link each batch to device identifiers, the method, the machine, the operator and the verification result. NIST Revision 2’s example certificate of sanitization lists the same kinds of fields. Our post on preparing R2v3 data sanitization evidence covers the wider evidence file.
7. Train and evaluate operators (Appendix B)
Appendix B requires data sanitization workers to be trained and evaluated for the methods they are authorized to perform. Keep a training record for every operator and verifier, with refresher dates. Start from our free NIST 800-88 training hub.
NIST 800-88 online training for operators
Give operators and verifiers a NIST SP 800-88 grounding before your audit: watch the NIST 800-88 online training and complete the quiz to obtain a NIST 800-88 training certificate.
Start the NIST 800-88 online training
Paradygm Consulting also offers NIST 800-88 training with a quiz and certificate on paradygm.co. It is educational awareness training and does not grant any NIST or other certification.
FAQ
What are the three R2v3 routes for physical destruction of data storage devices?
In summary, R2v3 Appendix B (7) allows a destruction method that Table 1 lists for that device type, the NSA Storage Device Sanitization Manual carried out with equipment that appears on NSA’s Evaluated Products List, or another physical destruction method that a competent expert has independently verified as effective.
How long must an R2v3 facility keep video of physical destruction?
In summary, R2v3 Appendix B (9) requires video of all physical destruction of media to be kept for a minimum of 60 days.
Is degaussing alone enough for hard drives under R2v3 Table 1?
No. In summary, Table 1 requires hard drives on the degauss route to be both degaussed and crushed in a hard drive crusher, and the degausser must carry the manufacturer's rating for the media type. NIST SP 800-88 Rev. 2 also says degaussing is not considered an approved destroy technique.
What if a customer contract requires stricter destruction than R2v3?
In summary, R2v3 Appendix B (8) requires the facility to apply the strictest requirement when a customer, a legal requirement or the sensitivity of the information calls for a more stringent destruction method.
Does NIST SP 800-88 apply to R2 facilities not certified to Appendix B?
SERI's guidance describes facilities outside Appendix B that physically destroy data devices in accordance with NIST's media sanitization guidelines.
Do R2v3 destruction equipment operators need training?
Yes. In summary, R2v3 Appendix B requires data sanitization workers to be trained and evaluated for the methods they are authorized to perform. Keep a training record for every operator and verifier, with refresher dates.
Related
- What changed in NIST SP 800-88 Rev. 2
- NIST SP 800-88 online training
- IEEE 2883 data sanitization training
- Free NIST 800-88 training hub
- Preparing R2v3 data sanitization evidence
- R2v3 standard requirements summary
Sources
- SERI, R2 Standard Version 3.0 (R2v3), effective July 1, 2020: Definitions and Appendix B – Data Sanitization
- SERI: Data Destruction/Sanitization Methods and Processing
- NIST SP 800-88 Rev. 2 (CSRC) · Full NIST SP 800-88 Rev. 2 (PDF) · SP 800-88r2 FAQ
- NSA Evaluated Products Lists (EPLs)
Last updated: 18 November 2026. Commentary by Paradygm Consulting. Not a substitute for the R2v3 Standard, SERI guidance, NIST SP 800-88, IEEE 2883 or NSA guidance.